£64.49 inc. vat£71.61save £7.12
£53.74 ex. vat£59.67save £5.93
Click & Collect Available
HyperX Fury Black 8GB (4GB x2) DDR4 2133MHz CL 14 Memory
- Hyperx Fury Black 8GB (4GB x2 Kit)
- 2133MHz Low Profile
- Automatic Overclocking
- Heat Spreader
- Factory Tested
Mfr part code: HX421C14FBK2/8
Customers Who Viewed This Product Also Viewed
£93.99 inc. vat£99.99save £6.00
£78.32 ex. vat£83.32save £5.00
£183.99 inc. vat£202.98save £18.99
£153.32 ex. vat£169.15save £15.83
HyperX Fury Black 8GB (4GB x2) DDR4 2133MHz CL 14 Memory Product Description
Plug and play
Get the speed you want, hassle free. HyperX FURY DDR4 is the first product line to offer automatic overclocking up to the highest frequency published.
Optimised for Intel's 200 Series and X99 chipsets
HyperX FURY DDR4 memory is 100% tested and optimised for compatibility and easy overclocking. To complete a motherboard featuring 200 Series or X99 chipsets, you need the latest generation of DRAM technology - DDR4 memory.
Low power consumption
DDR4's lower power requirements mean less heat and higher reliability. Low 1.2 volts draw less power from your system, which results in a cooler and quieter PC.
Low-profile stylish heat spreader
Stand out from the crowd and show your style with FURY's asymmetrical signature heat spreader. Available in black, red and white with black PCB, FURY DDR4's low profile heat spreader will fit under oversized CPU coolers while enhancing heat dissipation for lasting reliability.
HyperX HX421C14FBK2/8 is a kit of two 512M x 64-bit (4GB) DDR4-2133 CL14 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 512M x 8-bit FBGA components per module. Each module kit supports Intel Extreme Memory Profiles (Intel XMP) 2.0. Total kit capacity is 8GB. Each module has been tested to run at DDR4-2133 at a low latency timing of 14-14-14 at 1.2V.
- Power Supply: VDD = 1.2V Typical
- VDDQ = 1.2V Typical
- VPP - 2.5V Typical
- VDDSPD = 2.2V to 3.6V
- Nominal and dynamic on-die termination (ODT) for
data, strobe, and mask signals
- Low-power auto self refresh (LPASR)
- Data bus inversion (DBI) for data bus
- On-die VREFDQ generation and calibration
- On-board I2 serial presence-detect (SPD) EEPROM
- 16 internal banks; 4 groups of 4 banks each
- Fixed burst chop (BC) of 4 and burst length (BL) of 8
via the mode register set (MRS)
- Selectable BC4 or BL8 on-the-fly (OTF)
- Fly-by topology
- Terminated control command and address bus
- Height 1.230" (31.25mm), w/o heatsin
|Service & Support||Limited lifetime warranty (Russia - 10 years)||
|Capacity||8 GB: 2 x 4 GB|
|Speed||2133 MHz (PC4-17000)|
|Latency Timings||CL14 (14-14-14)|
|Features||Single rank, black heatsink, On-Die Termination (ODT), Black PCB, low profile heatspreader, FURY asymmetric heatspreader, sixteen banks, Intel Extreme Memory Profiles (XMP 2.0), unbuffered|
|Form Factor||DIMM 288-pin|
|Module Height (inch)||1.34|
|Data Integrity Check||Non-ECC|
|Module Configuration||512 x 64|
|Chips Organization||512 x 8|
HyperX Fury Black 8GB (4GB x2) DDR4 2133MHz CL 14 Memory Ask an owner
HyperX Fury Black 8GB (4GB x2) DDR4 2133MHz CL 14 Memory Product Discussion
Our comments box is a great way for you to view other people's feedback about products on Ebuyer.com, and add your own.
- This tool is open to everyone.
- You are responsible for the contents of your comments and any consequences that may arise as a result of them.
- Comments that contain any of the following will be deleted: terms considered explicit and inappropriate; defamatory, obscene, unlawful, harmful, or offensive.