£ 39.11 inc. vat
£ 32.59 ex. vat
Click & Collect Unavailable
HyperX Impact Black 4GB 1866MHz DDR3L CL11 SODIMM 1.35V
- 4GB 512M x 64-Bit DDR3L-1866
- 8 independent internal bank
- Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6, 5
- Factory Tested
QuickFind: 707759
Mfr part code: HX318LS11IB/4
{{#lists}}
{{ title }}
{{/lists}}
Customers Also Viewed
HyperX Impact Black 4GB 1866MHz DDR3L CL11 SODIMM 1.35V Product Description
HyperX HX318LS11IB/4 is a 512M x 64-bit (4GB) DDR3L-1866 CL11 SDRAM (Synchronous DRAM) 1Rx8, low voltage, memory modules, based on eight 512M x 8-bit DDR3 FBGA compo-nents. This module has been tested to run at DDR3L-1866 at a low latency timing of 11-11-11 at 1.35V or 1.5V. Additional timing parameters are shown in the PnP Timing Parameters section below.
FEATURES JEDEC standard 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V) Power Supply VDDQ = 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V) 933MHz fCK for 1866Mb/sec/pin 8 independent internal bank Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6, 5 Programmable Additive Latency: 0, CL - 2, or CL - 1 clock 8-bit pre-fetch
Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm 1%)
Burst Length: 8 (Interleave without any limit, sequential with starting address 000 only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe On Die Termination using ODT pin
FEATURES JEDEC standard 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V) Power Supply VDDQ = 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V) 933MHz fCK for 1866Mb/sec/pin 8 independent internal bank Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6, 5 Programmable Additive Latency: 0, CL - 2, or CL - 1 clock 8-bit pre-fetch
Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm 1%)
Burst Length: 8 (Interleave without any limit, sequential with starting address 000 only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS] Bi-directional Differential Data Strobe On Die Termination using ODT pin
Technical Specifications
Memory |
|
|---|---|
| Form Factor | SO-DIMM 204-pin |
| Speed | 1866 MHz (PC3L-14900) |
| Latency Timings | CL11 (11-11-11) |
| Features | Single rank, eight banks, On-Die Termination (ODT), Low Voltage, Black PCB, unbuffered |
| Type | DRAM |
| Technology | DDR3L SDRAM |
| Module Height (inch) | 1.18 |
| Data Integrity Check | Non-ECC |
| Module Configuration | 512 x 64 |
| Chips Organization | 512 x 8 |
| Voltage | 1.35 / 1.5 V |
| RAM Performance | SPD - 1333 MHz - 1.35 / 1.5 V - CL8 - 8-8-8 ¦ SPD - 1600 MHz - 1.35 / 1.5 V - CL10 - 10-10-10 ¦ SPD - 1866 MHz - 1.35 / 1.5 V - CL11 - 11-11-11 |
Manufacturer Warranty |
| Service & Support | Limited lifetime warranty (Russia - 10 years) |
General |
| Capacity | 4 GB |
| Upgrade Type | Generic |
HyperX Impact Black 4GB 1866MHz DDR3L CL11 SODIMM 1.35V Ask an owner
HyperX Impact Black 4GB 1866MHz DDR3L CL11 SODIMM 1.35V Product Discussion
Our comments box is a great way for you to view other people's feedback about products on Ebuyer.com, and add your own.
- This tool is open to everyone.
- You are responsible for the contents of your comments and any consequences that may arise as a result of them.
- Comments that contain any of the following will be deleted: terms considered explicit and inappropriate; defamatory, obscene, unlawful, harmful, or offensive.
