£ 161.99  inc. vat

£ 134.99 ex. vat

In Stock

Click & Collect Unavailable

Paypal Credit Finance from £14.55 a month.
(14.9% APR) representative

HyperX HX424C15FB2K2/16 16GB(2x8GB) 2400MHz DDR4 Memory

  • Selectable BC4 or BL8 on-the-fly (OTF)
  • Fly-by topology
  • Terminated control command and address bus
  • Data bus inversion (DBI) for data bus
  • On-die VREFDQ generation and calibration

View full description

QuickFind: 743585

Mfr part code: HX424C15FB2K2/16

{{#lists}}
  • {{ title }}
  • {{/lists}}

    HyperX HX424C15FB2K2/16 16GB(2x8GB) 2400MHz DDR4 Memory Product Description

    HyperX Fury 16GB (2X8GB) DDR4 2133MHz CL14 DIMM Black Memory Kit

    DESCRIPTION

    HyperX HX424C15FB2K2/16 is a kit of two 1G x 64-bit (8GB) DDR4-2400 CL15 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 1G x 8-bit FBGA components per module. Each module kit supports Intel Extreme Memory Profiles (Intel XMP) 2.0. Total kit capacity is 16GB. Each module has been tested to run at DDR4-2400 at a low latency timing of 15-15-15 at 1.2V. Additional timing parameters are shown in the Plug-N-Play (PnP) Timing Parameters section below. The JEDEC standard electrical and mechanical specifications are as follows:

    Note: The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS.

    JEDEC/XMP TIMING PARAMETERS
    JEDEC/PnP: DDR4-2400 CL15-15-15 @1.2V
    DDR4-2133 CL14-14-14 @1.2V
    XMP Profile #1: DDR4-2400 CL15-15-15 @1.2V

    SPECIFICATIONS

    • CL(IDD) 15 cycles
    • Row Cycle Time (tRCmin) 46.75ns(min.)
    • Refresh to Active/Refresh Command Time (tRFCmin)  350ns(min.)
    • Row Active Time (tRASmin) 29.125ns(min.)
    • Maximum Operating Power TBD W*
    • UL Rating 94 V - 0
    • Operating Temperature  0oC to +85oC
    • Storage Temperature -55oC to +100oC

    *Power will vary depending on the SDRAM used.

    FEATURES

    • Power Supply: VDD = 1.2V Typical
    • VDDQ = 1.2V Typical
    • VPP - 2.5V Typical
    • VDDSPD = 2.2V to 3.6V
    • Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals
    • Low-power auto self refresh (LPASR)
    • Data bus inversion (DBI) for data bus
    • On-die VREFDQ generation and calibration
    • Single-rank
    • On-board I2 serial presence-detect (SPD) EEPROM
    • 16 internal banks; 4 groups of 4 banks each
    • Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS)
    • Selectable BC4 or BL8 on-the-fly (OTF)
    • Fly-by topology
    • Terminated control command and address bus
    • Height 1.340" (34.04mm), w/o heatsink

    Technical Specifications

    General

    Capacity 16 GB: 2 x 8 GB
    Upgrade Type Generic

    Memory

    Speed 2400 MHz (PC4-19200)
    Latency Timings CL15 (15-15-15)
    Features Single rank, black heatsink, On-Die Termination (ODT), Serial Presence Detect (SPD), dual channel, Black PCB, low profile heatspreader, FURY asymmetric heatspreader, sixteen banks, Intel Extreme Memory Profiles (XMP 2.0), unbuffered
    Type DRAM
    Technology DDR4 SDRAM
    Form Factor DIMM 288-pin
    Module Height (inch) 1.34
    Data Integrity Check Non-ECC
    Module Configuration 1024 x 64
    Chips Organization 1024 x 8
    Voltage 1.2 V
    Lead Plating Gold
    RAM Performance SPD - 2133 MHz - 1.2 V - CL14 - 14-14-14 ¦ SPD - 2400 MHz - 1.2 V - CL15 - 15-15-15 ¦ Intel Extreme Memory Profiles (XMP 2.0) - 2400 MHz - 1.2 V - CL15 - 15-15-15

    Manufacturer Warranty

    Service & Support Limited lifetime warranty (Russia - 10 years)

    Miscellaneous

    Colour Category Black

    HyperX HX424C15FB2K2/16 16GB(2x8GB) 2400MHz DDR4 Memory Ask an owner

    HyperX HX424C15FB2K2/16 16GB(2x8GB) 2400MHz DDR4 Memory Product Discussion

    Our comments box is a great way for you to view other people's feedback about products on Ebuyer.com, and add your own.

    • This tool is open to everyone.
    • You are responsible for the contents of your comments and any consequences that may arise as a result of them.
    • Comments that contain any of the following will be deleted: terms considered explicit and inappropriate; defamatory, obscene, unlawful, harmful, or offensive.