HyperX Fury Black Series 4GB 1866MHz DDR3 CL10 DIMM Memory
QuickFind: 633831
Mfr part code: HX318C10FB/4
- Easy to install - features plug-and-play functionality
- Automatic overclocking - reach faster speeds and higher capacities by installing the...
- Reliable - 100% factory tested
Product Description
HyperX Fury Black Series 4GB 1866MHz DDR3 CL10 DIMM Memory
SPECIFICATIONS
CL(IDD) 10 cycles
Row Cycle Time (tRCmin) 44.75ns (min.)
Refresh to Active/Refresh 260ns (min.) Command Time (tRFCmin)
Row Active Time (tRASmin) 32.125ns (min.)
Maximum Operating Power TBD W*
UL Rating 94 V - 0
Operating Temperature 0oC to 85o C
Storage Temperature -55oC to +100o C
*Power will vary depending on the SDRAM used.
FEATURES
• JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 933MHz fCK for 1866Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with starting address "000" only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB : Height 1.180" (30.00mm), single sided component
CL(IDD) 10 cycles
Row Cycle Time (tRCmin) 44.75ns (min.)
Refresh to Active/Refresh 260ns (min.) Command Time (tRFCmin)
Row Active Time (tRASmin) 32.125ns (min.)
Maximum Operating Power TBD W*
UL Rating 94 V - 0
Operating Temperature 0oC to 85o C
Storage Temperature -55oC to +100o C
*Power will vary depending on the SDRAM used.
FEATURES
• JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 933MHz fCK for 1866Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 13, 11, 10, 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with starting address "000" only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB : Height 1.180" (30.00mm), single sided component
Technical Specification
HyperX Fury Black Series 4GB 1866MHz DDR3 CL10 DIMM Memory
Memory |
|
|---|---|
| Speed | 1866 MHz (PC3-14900) |
| Latency Timings | CL10 (10-10-10-30) |
| Features | Black PCB, FURY asymmetric heatspreader, unbuffered |
| Type | DRAM |
| Technology | DDR3 SDRAM |
| Form Factor | DIMM 240-pin |
| Module Height (inch) | 1.29 |
| Data Integrity Check | Non-ECC |
| Module Configuration | 512 x 64 |
| Voltage | 1.5 V |
| Lead Plating | Gold |
Manufacturer Warranty |
|
| Service & Support | Limited lifetime warranty (Russia - 10 years) |
General |
|
| Capacity | 4 GB |
| Upgrade Type | Generic |
Expansion / Connectivity |
|
| Compatible Slots | 1 x memory - DIMM 240-pin |
Miscellaneous |
|
| Colour Category | Black |
Product Reviews
Ask an Owner
HyperX Fury Black Series 4GB 1866MHz DDR3 CL10 DIMM Memory
Sorry, customer questions are not available for this product.
Product Discussion
HyperX Fury Black Series 4GB 1866MHz DDR3 CL10 DIMM Memory
Our comments box is a great way for you to view other people's feedback about products on Ebuyer.com, and add your own.
- This tool is open to everyone.
- You are responsible for the contents of your comments and any consequences that may arise as a result of them.
- Comments that contain any of the following will be deleted: terms considered explicit and inappropriate; defamatory, obscene, unlawful, harmful, or offensive.